An FMT engineer replies within one working day. Budget prices from tank size and duty. +91 73852 62875WhatsAppsales@fluidmixtech.comExport buyers

Hydrogenators and high pressure reactors

Stirred reactors for gas-liquid reactions under pressure, such as catalytic hydrogenation: the gas has to be dispersed into the liquid, the catalyst kept in suspension and the pressure safely contained.

An FMT engineer replies within one working dayBudget price from tank size and duty

Agitator drive and lantern on a heavy bolted reactor cover
Agitator drive and lantern on a heavy bolted reactor cover

In a hydrogenation the reaction can only go as fast as hydrogen dissolves in the liquid and reaches the catalyst, so the agitator does most of the work. It draws gas into the liquid, breaks it into fine bubbles and keeps the solid catalyst in suspension. A gas-inducing agitator, with a hollow shaft that sucks gas from the headspace and releases it at the impeller, recirculates unreacted gas without a compressor.

The vessel and its fittings are designed for the pressure and temperature of the reaction: a flanged and bolted closure, pressure relief by safety valve and rupture disc, and a shaft seal chosen to keep the gas in. Heating and cooling is by jacket or limpet coil, with internal coils where the heat of reaction is high. We design each reactor for the specific reaction and the design conditions you give us.

Where it is used

  • Catalytic hydrogenation
  • Other gas-liquid reactions under pressure
  • Polymerisation under pressure
  • Reactions above the boiling point of the solvent
  • Batch reactions with a slurry catalyst

How FMT builds it

Design codeASME Section VIII or PED on request
AgitatorGas-inducing hollow-shaft impeller, or a gas-dispersing turbine with a sparger
CatalystImpeller arrangement that keeps the catalyst in suspension
ClosureFlanged and bolted top head or cover
Shaft sealDouble mechanical seal with a pressurised barrier system
Heating / coolingJacket or limpet coil; internal coils for a high heat of reaction
SafetySafety valve and rupture disc, pressure gauge and switch, temperature measurement
MaterialsSS 316 / 316L; other alloys on request
Typical arrangement

The red lines show how the impeller moves the liquid. Every FMT unit is sized for its own vessel, product and duty, so yours is drawn for your tank in the offer.

Send your vessel for a drawing
Gearbox, lantern and seal housing of a reactor agitator on its bolted cover
Gearbox, lantern and seal housing of a reactor agitator on its bolted cover

What we need to size it

  • The reaction, the catalyst and its loading
  • Batch volume and liquid level, allowing for the gas held up in the liquid
  • Design pressure and temperature
  • The gas: composition, supply pressure and whether it is recirculated
  • Heat of reaction and the cooling medium available
  • Hazardous-area classification and the safety requirements of your plant
Send what you have. A vessel drawing and a short description of the product and duty is enough to start; we ask for anything else we need. Send an enquiry

Common questions

What is a gas-inducing agitator?
An agitator with a hollow shaft and a special impeller. As the impeller turns it creates suction that draws gas from the headspace down the shaft and disperses it into the liquid. Unreacted gas returns to the headspace and is drawn in again, so gas use is high without an external compressor.
Why does the agitator matter so much in hydrogenation?
Because the reaction rate is usually limited by how fast hydrogen dissolves. A good gas-dispersing agitator creates more gas-liquid contact area, which can shorten a batch far more than raising the pressure or temperature.
Which shaft seal is used for hydrogen service?
Usually a double mechanical seal with a pressurised barrier fluid, so that any leakage is barrier fluid into the reactor rather than gas to atmosphere. The seal and its barrier system are chosen for the design pressure and temperature.

Send us your vessel. We size the agitator.

Tank size, product and what the agitator has to do is enough to start. Send a drawing, a datasheet or just a photo of the tank, and we reply with a recommended design and price, or a budget price first if you need one.

An FMT engineer replies within one working day.