An FMT engineer replies within one working day. Budget prices from tank size and duty. +91 73852 62875WhatsAppsales@fluidmixtech.comExport buyers

Batch vs inline blending: which suits your chemical plant?

How batch and inline (continuous) blending compare on flexibility, quality control, powders, changeovers, output and space, and when to combine the two.

Two ways to blend

Every blending plant has to bring several components together in the right proportions and mix them until the product is uniform. There are two basic ways to do it. In batch blending, the components are added one after another to an agitated tank, mixed, checked and then pumped out. In inline, or continuous, blending, each component is metered at the right rate into a common pipe, where an inline mixer combines them and the finished product flows straight to storage or filling.

How batch blending works

The blend tank is charged with each ingredient in turn, usually by weight, while the agitator runs. When the batch is complete it is mixed for a set time, sampled and tested. If the result is off, the batch is adjusted and tested again; when it passes, it is released and transferred. Accuracy comes from the weighing system, and uniformity from the agitator and the mixing time.

How inline blending works

Each component has its own pump and flow meter, and a controller holds each flow at its share of the total. The streams meet at a manifold and pass through an inline mixer. Quality depends on the accuracy of the meters and on keeping every flow steady, including at start-up and shutdown, when the proportions are hardest to hold. Product is often checked by an analyser in the line or by sampling at intervals.

Side by side

Batch blendingInline blending
Number of productsMany, with frequent recipe changesFew, with stable recipes
Quality controlEach batch tested and adjusted before releaseDepends on meter accuracy and steady flows
Powders and solidsEasy to add to an agitated tankDifficult; usually premixed first
Viscous productsHandled with the right agitatorHarder to meter and mix in a pipe
ChangeoversClean or flush the tank and linesFlush the line; some off-spec product at start and end
OutputLimited by tank size and batch cycle timeHigh for its size
SpaceBlend tanks, plus storage for finished productCompact; little intermediate storage
ControlsSimple to automaticNeeds flow control and instrumentation from the start

When batch blending is the better choice

  • The plant makes many products, or customers order small quantities
  • Each batch must be tested and released, or traced, before it leaves
  • Recipes include powders, viscous components or small additions that are hard to meter
  • Products are developed or adjusted often
  • The plant is starting up and the product mix is not yet settled

This describes most specialty, oilfield and agrochemical plants, which is why batch blending is the usual starting point.

When inline blending is the better choice

  • A few products are made in large, steady volumes
  • All components are liquids that meter well
  • Space for tanks is short
  • Product goes straight to large containers or bulk loading

Combining the two

Many plants use both. A common arrangement is to make a base or premix in batch tanks, where powders and difficult components are handled, and then add a final component inline at filling. Another is to blend in batches for small products and run the largest product inline. A semi-continuous plant of this kind keeps the quality control of batches while gaining throughput where it counts.

Where the agitator fits in

In a batch plant, the blend tank agitator does the mixing, so it has to be sized for the hardest product on the list and for mixing at low level as the tank fills and empties. In an inline plant, agitators still appear in premix and additive tanks. Either way, getting the mixing right is what makes the product consistent. See chemical blending plants for how FMT engineers complete plants, or send us your product list for a recommendation.

Send us your vessel. We size the agitator.

Tank size, product and what the agitator has to do is enough to start. Send a drawing, a datasheet or just a photo of the tank, and we reply with a recommended design and price, or a budget price first if you need one.

An FMT engineer replies within one working day.