An FMT engineer replies within one working day. Budget prices from tank size and duty. +91 73852 62875WhatsAppsales@fluidmixtech.comExport buyers

Blending oilfield chemicals: what demulsifiers, inhibitors and biocides need from the plant

How demulsifiers, corrosion and scale inhibitors, biocides, defoamers and drilling chemicals differ in blending, and what that means for tanks and agitators.

An oilfield chemical plant rarely makes one product. The same site usually blends demulsifiers, corrosion inhibitors, scale inhibitors, biocides, defoamers and drilling additives, each to several formulations for different fields and crudes. These products behave differently in the blend tank, and some must never meet. Planning the plant around those differences decides how many tanks it needs, which agitators, and how changeovers work.

Demulsifiers

Demulsifiers (emulsion breakers) are blends of several active polymers in a solvent, often aromatic solvent or alcohol. The actives can be viscous, sometimes waxy, and a formulation may combine three or four of them. The blend tank needs an agitator that pulls viscous actives down into the solvent and keeps the batch turning over until it is uniform, and enough heating to bring thick actives to a workable viscosity.

Because the solvents are flammable, demulsifier blending is almost always done in a hazardous area, with closed tanks, a mechanical seal on the agitator and a flameproof drive.

Corrosion inhibitors

Corrosion inhibitors are commonly made from film-forming actives such as amines and imidazolines, dissolved or dispersed in water or solvent, sometimes with surfactants. Some formulations are water-dispersible and foam readily, so the agitator should blend thoroughly without drawing air into the batch: a vortex at the surface is a sign of the wrong impeller or speed. Many actives are corrosive in concentrated form, which sets the material of the tank, the impellers and the seal faces.

Scale inhibitors

Scale inhibitors are usually water-based solutions of phosphonates or polymers, often neutralised during blending. Neutralisation releases heat and needs good bulk mixing so that the pH is even before the batch is sampled. Products are thin and easy to mix, but they are acidic or alkaline at different stages, so stainless steel grades and gasket materials need checking against each formulation.

Biocides

Biocides are toxic by design. The concern in the plant is containment more than mixing: closed charging, closed tanks, a double mechanical seal where vapour or leakage to atmosphere is not acceptable, and dedicated or well-flushed lines so that no biocide carries over into another product. Some biocides are incompatible with other actives in the plant, which is a reason to give them their own tank.

Defoamers and drilling additives

Defoamers are often silicone or oil-based emulsions and may need high shear to disperse the active properly; a rotor-stator or high shear mixer in the blend tank, or in a recirculation loop, does this. Drilling additives include powders such as polymers and viscosifiers that must be wetted without forming lumps, which calls for a powder induction point or a disperser and a viscous-capable agitator, because the product thickens as the powder hydrates.

What this means for the plant

  • Tank allocation. Group products that can share a tank with a simple flush, and give dedicated tanks to products that must not meet, such as biocides and some inhibitor packages.
  • Agitator sizing. Size each blend tank agitator for the most demanding product it will make, usually the most viscous one or the one with powder, and use variable speed where thin and thick products share a tank.
  • Heating. Plan jackets or coils where viscous or waxy actives are charged, and insulate lines that carry them.
  • Containment. Use closed tanks, mechanical seals and flameproof drives for solvent-based products, and a double seal for toxic ones.
  • Dosing. Load cells or flow meters for the actives, which are dosed in small proportions and decide performance; calibrated tanks may be enough for the bulk solvent or water.
  • Changeovers. Lines and tanks that drain fully, short dead legs and a flush procedure between products.

Start from the product list

The quickest way to a sound design is a table of every product the plant will make: the actives and solvents in each, typical proportions, batch size, how often it is made and how it is packed. From that we work out the number and size of blend tanks, which share and which are dedicated, the agitator for each, and the tank farm behind them. See our oilfield chemical blending plants page, or send your product list for a first layout and budget price.

Send us your vessel. We size the agitator.

Tank size, product and what the agitator has to do is enough to start. Send a drawing, a datasheet or just a photo of the tank, and we reply with a recommended design and price, or a budget price first if you need one.

An FMT engineer replies within one working day.