An FMT engineer replies within one working day. Budget prices from tank size and duty. +91 73852 62875WhatsAppsales@fluidmixtech.comExport buyers

Jacket, limpet coil or dimple jacket: choosing reactor heating and cooling

How conventional jackets, limpet (half-pipe) coils, dimple jackets and internal coils compare for pressure, heat transfer, media, cost and cleaning.

Why the heating and cooling arrangement matters

In most batch reactors, heating and cooling take longer than the reaction itself. The batch has to be brought up to temperature, held there while the heat of reaction is removed, and cooled before it is discharged. How long that takes, and whether an exothermic reaction stays under control, depends on how much heat can pass through the vessel wall.

That depends on three things: the heat transfer area, the temperature difference between the medium and the product, and how well heat crosses the two films on either side of the wall. The arrangement outside the shell, whether a jacket, a limpet coil or a dimple jacket, decides the outside film and the pressure the medium can be used at. The agitator decides the inside film.

Conventional jacket

A conventional jacket is a second, larger shell welded around the vessel, leaving an annular space through which the medium flows. It usually covers the cylindrical shell and the bottom head.

  • Strengths: simple, economical, a large heat transfer area, and well suited to condensing steam, which spreads through the whole space
  • Limits: the jacket pressure acts on the full area of the inner shell, so higher jacket pressures need a much thicker vessel wall; with liquids such as water or thermic oil the flow spreads out and slows down, which lowers heat transfer unless the inlet nozzles or internal baffles direct it
  • Best for: steam and water at modest pressure, smaller vessels, and duties where simplicity and cost matter most

Limpet coil (half-pipe coil)

A limpet coil is a pipe cut in half along its length and welded in a spiral around the shell and bottom. The medium follows a single, narrow path at high velocity.

  • Strengths: the small half-pipe section stands much higher pressure than a full jacket without thickening the vessel wall; the fast, directed flow gives good heat transfer with liquids and avoids dead zones; the coil also stiffens the shell
  • Limits: more welding, so it costs more to make; the pressure drop along a long coil is higher, which affects the circulation pump; the coil can be split into zones to manage this
  • Best for: thermic oil, high-pressure steam, hot water circulation and larger reactors

Dimple jacket

A dimple jacket is a thin sheet pressed with a regular pattern of dimples, which are welded through to the vessel shell. The dimples support the sheet against the internal pressure and make the medium flow turbulently.

  • Strengths: light and economical for its pressure rating, with good heat transfer from the turbulent flow
  • Limits: the narrow passages are harder to clean and inspect, and the fatigue life of the welds needs care where temperatures cycle widely
  • Best for: moderate pressures, large shells where weight matters, and cooling duties with water or glycol

Internal coils

When the wall alone does not give enough area for a high heat of reaction, or the vessel is large and its wall area is small for its volume, a coil inside the vessel adds area. Internal coils transfer heat well because the product flows over both sides of the pipe, but they get in the way of the flow pattern, are harder to clean, and must be designed with the agitator so that the impellers still turn the whole batch over.

Side by side

Conventional jacketLimpet coilDimple jacket
Pressure of the mediumLow to moderateHighModerate
Heat transfer with liquidsFair, better with directed flowGood: fast, directed flowGood: turbulent flow
SteamVery suitable at low pressureSuitable, including high pressureSuitable at moderate pressure
Thermic oilPossibleUsual choicePossible
Effect on vessel wallWall must carry jacket pressureLittle; coil also stiffens the shellLittle
Cost and weightLowest costHighest fabrication costLight, economical
Cleaning and inspectionEasy to drain and flushStraightforwardHarder

How the medium decides the choice

  • Steam condenses and spreads through the space by itself, so a conventional jacket works well at low pressure; at higher steam pressures a limpet coil avoids a very thick vessel wall
  • Thermic oil needs velocity to transfer heat well, and is often used at high temperature, so a limpet coil is the usual choice
  • Hot and cold water, chilled water and glycol also need velocity; a limpet coil or dimple jacket, or a jacket with directed inlets, gives it
  • Heating and cooling in the same batch needs an arrangement that can be drained and switched between media, or a single thermal fluid loop that is heated and cooled outside the reactor

Do not forget the agitator

A well-chosen jacket is wasted if the product inside barely moves past the wall. In thin liquids a hydrofoil or pitched blade turbine at the right speed keeps the inside film thin. In viscous batches, where the inside film dominates, an anchor that sweeps close to the wall, often with scrapers, can make more difference than any change outside the shell. Size the agitator and the heat transfer surface together.

Zones and partial batches

If the reactor runs part full, only the wetted part of the wall transfers heat; a jacket or coil above the liquid wastes the medium and can overheat the product film. Splitting the jacket or coil into zones, bottom and shell, or lower and upper shell, lets you heat or cool only the wetted area.

What to send us

To recommend an arrangement we need the batch volume and levels, the product properties through the batch, the temperature profile with the times allowed, the heat of reaction, and the heating and cooling media available with their temperatures and pressures. See jacketed and limpet coil reactors and chemical reactors, or send an enquiry.

Send us your vessel. We size the agitator.

Tank size, product and what the agitator has to do is enough to start. Send a drawing, a datasheet or just a photo of the tank, and we reply with a recommended design and price, or a budget price first if you need one.

An FMT engineer replies within one working day.