An FMT engineer replies within one working day. Budget prices from tank size and duty. +91 73852 62875WhatsAppsales@fluidmixtech.comExport buyers

How to set up a chemical blending plant: a step-by-step guide

Planning a chemical blending plant: product list, batch size, raw material storage, dosing, blend tanks and agitators, changeovers, hazardous areas and layout.

Start from the product list

A blending plant is designed backwards from what it has to make. Before any tank is sized, write down every product the plant will make in its first years, with a typical recipe for each: the raw materials, their proportions and the order in which they go in. Note which products are thin liquids, which are viscous, which take powders, and which must never come into contact with each other.

This list drives almost every later decision. A plant that makes three high-volume products is a different plant from one that makes forty products in small lots, even if the daily output is the same.

Decide the batch size and the daily output

From the sales forecast, work out how much of each product is needed per day or per month, then how many batches that means. The batch size is usually a compromise: larger batches mean fewer changeovers and less labour per tonne, while smaller batches suit small orders, frequent recipe changes and products with a short shelf life.

Count the time each batch spends in the blend tank, not just the mixing time: charging, mixing, sampling, waiting for the laboratory result, adjusting, and emptying. Quality control hold time often decides how many blend tanks the plant needs.

Choose batch, semi-continuous or inline blending

Most specialty and oilfield chemical plants blend in batches, because batches are flexible and each one can be tested before it is released. Plants that make a few products in large volumes may blend inline, metering the components continuously into a pipe. A semi-continuous plant sits in between, for example by preparing a premix in batches and then dosing it continuously. Our article on batch vs inline blending compares the options in detail.

Plan raw material receipt and storage

How each raw material arrives decides the storage it needs:

  • Bulk liquids from road tankers need storage tanks, an unloading point and a transfer pump
  • Drums and IBCs need an unloading area and a way to empty them into the plant, by pump or by gravity
  • Powders and flakes in bags need a charging point at the blend tank, with dust extraction where the powder is hazardous
  • Viscous or waxy raw materials may need heated storage or a drum heating area before they can be pumped

Keep incompatible raw materials apart in storage, with separate bunds where a leak from one could react with another.

Get the dosing right

The accuracy of the finished product can be no better than the accuracy of the dosing. Batch plants usually weigh: the blend tank sits on load cells and each ingredient is added until the weight is reached. Flow meters are used where tanks cannot be weighed, or for inline dosing. Small additions such as dyes, biocides or a final additive are often weighed separately and charged by hand.

The order of addition matters too. Many products need the solvent first, then the actives, then additives that only dissolve or disperse well in the finished base.

Size the blend tank and its agitator for the hardest product

The blend tank agitator has to handle the most demanding product on the list, not the average one. A thin solvent blend needs good top-to-bottom turnover; a viscous polymer solution needs a larger, slower impeller and more torque; a product that takes powder needs a disperser or rotor-stator mixer to wet the powder and break up lumps. Check also whether mixing must continue while the tank is filling or emptying, which decides how low the bottom impeller must sit.

Other points to settle with the tank design: a jacket if products must be heated or cooled, baffles to stop the liquid simply swirling, a nozzle layout that leaves room for the agitator and its maintenance, and a bottom outlet that lets the tank drain completely. Our guide to choosing agitators for blending tanks goes through the options.

Transfer, filtration and filling

Finished product is pumped from the blend tank, usually through a filter, to storage tanks or straight to filling. Choose pumps for the viscosity range of the products and for the flammability of the area. Filling can be by weight or by volume, into drums, IBCs or road tankers, and needs its own space for empty and full containers.

Design for changeovers

In a multi-product plant, changeovers cost more time than mixing. Tanks and lines that drain completely, short pipe runs without dead legs, and a clear plan of which products share tanks and lines make changeovers quick. Where one product would spoil another, give it dedicated equipment or a flush and drain step between batches.

Plan for hazardous areas and safety

Many chemical blends are made with flammable solvents. The flash points of the raw materials and products, and the way they are handled, decide the hazardous-area classification of each part of the plant. That classification in turn decides the motors, instruments, lighting and electrical work. Earthing and bonding of tanks and containers, spill containment, ventilation and safe access for operators belong in the design from the start, not added afterwards.

Decide the level of control

A small plant can run with manual valves, local start buttons and paper batch records. As the number of products and batches grows, automatic control pays for itself: stored recipes, automatic dosing by weight, agitator speed control, interlocks that stop a wrong addition, and batch records kept electronically. Many plants start simple and add automation later, so allow for it in the instrument and cable design.

Lay out the plant

A good layout keeps pipe runs short, uses gravity where it can, and gives every agitator, pump and filter room for maintenance, including the headroom to lift an agitator out of its tank. Leave space and connections for the tanks the plant will need when it grows.

What to send for a quote

To quote a blending plant we need the product list with typical recipes, the batch size or daily output, how raw materials arrive and products leave, the hazardous-area classification and the site location. A process description is enough to start; we propose the plant arrangement and the equipment. See chemical blending plants and oilfield chemical blending plants, or send us an enquiry.

Send us your vessel. We size the agitator.

Tank size, product and what the agitator has to do is enough to start. Send a drawing, a datasheet or just a photo of the tank, and we reply with a recommended design and price, or a budget price first if you need one.

An FMT engineer replies within one working day.